MANUAL
TABLE OF CONTENTS
Contact & Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Table Of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Foreword - by Frank Filipetti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
DSP Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Overview & parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Presets menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Default preset locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
A/B compare function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Tube-Tech CL 1B / 3
Foreword - by Frank Filipetti
As an engineer/producer I am constantly amazed by the sheer number of new (and
vintage) equipment available to us. And yet, more often than not, I find myself
returning to those few trusted pieces of gear that in a certain sense define our
individual sound. One of those pieces that I would never want to be without is my
Tube-Tech CL 1B. Sometime in the mid 80’s, I was contacted by John Petersen and
offered a chance to play with a prototype of their first compressor – the CL 1A. I
remember at the time being very impressed, but I had a few reservations and
suggestions about the product. While not suggesting my recommendations led to the
final CL 1B, I was very impressed to find that, not only was every one of my thoughts
addressed, but a great deal more as well.
Since the introduction of the CL 1B it has been an essential element in my
recordings. While exhibiting the characteristic warmth of tube equipment, it is by no
means soft or slow. The fixed and variable attack and release knobs as well as variable
threshold and ratio give me all the flexibility left wanting in vintage
compressor/limiters. With quick attack and release at a ratio of 1.5:1 or 2:1 it is my
number one choice for vocal recording. With longer attack and release times at higher
ratios I use it for everything from bass drum to acoustic guitar to piano to bass. In
fact, about the only thing I don’t use it for is mix buss compression as that is handled
by my indispensable Tube-Tech SMC 2B.
Frank Filipetti.
Biography:
Frank Filipetti came to NY as a singer songwriter in 1971. Ten years, two publishing,
and three record deals later, he decided to try his hand at engineering and production.
He had his first number one single in 1983 with Foreigner’s “I Want To Know What
Love Is”. Since then he has worked on projects with artists as varied as James Taylor,
Kiss, Luciano Pavarotti, Courtney Love, Barbra Streisand, Dave Grusin, Korn, Carly
Simon, Elton John, Mariah Carey, Rod Stewart, and Paul McCartney; on film
soundtracks for directors Mike Nichols and Nora Ephron. In 1998 he won two
personal Grammy’s for his engineering and production work on James Taylor’s
“Hourglass”, and in 2000, 2004, and 2005 he won Grammy’s for his engineering and
production work on the Original Cast albums of “Aida”, “Wicked” and “Spamalot”.
Recently he has been at the forefront in 5.1 surround mixing. The N2K album “Dave
Grusin – West Side Story”, which he recorded and mixed with producer Phil Ramone
in 1997, was one of the first commercially available 5.1 recordings. Since then he
has done numerous 5.1 mixes for artists such as James Taylor, Meatloaf, Billy Joel,
Five For Fighting, Elton John, Polyphonic Spree, Paul Simon and Frank Zappa.
System Requirements
Windows
Mac OS X
PowerCore software 2.2 or higher
Windows XP
PIII 1,4 GHz or faster
512 MB RAM
PowerCore software 2.2 or higher
Mac OS X (10.4 or higher)
G4/G5 or Intel (1 GHz or faster)
512 MB RAM
VST compatible host application
System must meet requirements of the
host application
VST, Audio Units or RTAS*) compatible
host application.
System must meet requirements of the
host application
*) RTAS (Pro Tools) is supported via the VST to RTAS adapter from FXpansion (optional).
Getting Started
Scroll Wheel Support
If you are using a host application that supports this feature, all parameters support
scrolling on both Windows XP and Mac OS X. Simply place the mouse over a
parameter value field and use the Scroll Wheel to increment/decrement the associated
parameter-value.
Key Commands
In most host applications, Plug-Ins support keyboard commands for certain functions.
The following key commands are available for all Plug-In parameters.
Key Commands in Mac OS
Reset To Default = Alt
Key Commands In Windows
Reset To Default = Shift & Control
DSP Usage
For each open instance of the CL 1B on 1st generation PowerCore devices
(PowerCore Element and PowerCore PCI), the following DSP usage applies:
88.2 and 96 kHz sample rates are
not supported on 1st generation
PowerCore hardware.
@44.1 kHz:
mono 49%
stereo 61%
@48 kHz:
mono 54%
stereo 67%
For each open instance of the CL 1B on 2nd generation PowerCore devices (Express,
PCI mkII, Unplugged, Compact & FireWire), the following DSP usage applies :
@44.1 kHz:
mono 33%
stereo 41%
@48 kHz:
mono 36%
stereo 45%
@88.2 kHz:
mono 69%
stereo 85%
@96 kHz:
mono 76%
stereo 93%
Tube-Tech CL 1B / 5
Overview & parameters
1 - In switch
CL 1B has two bypass functions. The IN switch activates/deactivates the processing,
but leaves the meter functions working. Using the IN switch to bypass the plug-in, the
plug-in is still loaded onto the PowerCore DSPs and the CL 1B can therefore instantly
be switched in and out.
2 - Gain
The gain control is used to compensate for the gain loss during compression. It is
placed after the gain-reduction section and therefore it has no influence on the
threshold setting. The gain control is continuously variable from off to +30 dB.
3 - Ratio
The ratio control varies the ratio by which the input signal is compressed. If the ratio
set to 2:1, and the input signal increases 10 dB, the output signal is only increased
by 5 db. The ratio control is continuously variable from 2:1 to 10:1.
4 - Threshold
When the signal is above the set threshold point, the compressor is activated and the
gain of any signal above the Threshold point is processed according to the ratio,
attack and release settings.
5/6 - Meter
Input: The VU-meter displays the input level.
Compression: The VU-meter displays the gain reduction. The meters neutral position is
at "0 VU", and the amount of compression is shown as a decrease in dB.
Output: The VU-meter displays the output level.
6 / Tube-Tech CL 1B
Enhanced VU-meter function:
Pressing
in the lower left side of the meter allows you to change between
three meter states.
L:
Meter indicates left channel only
R:
Meter indicates right channel only
L+R:
Meter indicates both left and right channels
7 - Off/On
To bypass CL 1B and free PowerCore DSP resources at the same time, set the Off/On
switch to “Off”. - See also the description of the IN switch.
8 - Attack
The attack control determines how fast the compressor responds to an increase of the
input signal. The attack control is continuously variable from 0.5 to 300 milliseconds.
9 - Release
The release control determines how fast the compressor responds to a decrease of the
input signal. The release control is continuously variable from 0.05 to 10 seconds.
10 - Attack/Release Select
Three options are available
Fixed:
Attack time: 1 msec
Release time: 50 msec
Manual: Attack time: from 0.5 msec to 300 msec
Release time: from 0.05 sec to 10 sec
Fix/man: This setting is mainly intended as an overall compression on a full mix or on
a sub-group mix. Combining the release times of Fixed and Manual modes, the
Fix/man mode facilitates an adaptive release function with fast constant attack and
release times for short peaks and a longer release times for longer peaks.
•
•
Turn the Attack control counter-clockwise to increase the time before the release
control takes over
Turn the Attack control clockwise to decrease the time before the release control
takes over
Notice that the Fix/man mode is in effect only when the peak-time is shorter than the
setting of the attack control. If the peak of signal is longer than the setting of the
attack control, or if the attack control is set fully counter-clockwise, it will respond as
in manual mode.
Tube-Tech CL 1B / 7
11 - Sidechain Link
The Sidechain Link function is relevant only when CL 1B is used on a stereo audio
file. In Left+Right mode it creates a dynamic master/slave relation between right and
left channels, allowing the channel where most compression is applied to also control
the compression amount of the other channel. This is similar to the sidechain
functionality you have available when connecting two hardware CL 1B (mono) units for
the purpose of processing in stereo.
In Left mode the compression amount applied on the left channel also controls the
compression amount applied on the right channel. In Right mode we have the exact
opposite situation.
8 / Tube-Tech CL 1B
Presets section
Via the Presets section you are able to recall, store and compare different settings.
12 - File
Press FILE to open the File menu.
Load Preset: Select to load presets from the default preset location.
Save Preset: Select to save the preset in My Presets folder.
My Presets: Via “My Presets” you are able to load you own presets.
If you chose to store presets in other locations than the “My Preset” folder,
these presets will not appear in the “My Preset” drop down menu. However, you
can still navigate to, and load these presets via the Load Preset function.
13 - Preset name
This is the name of the preset.
Default Preset Locations
The following locations will describe where you can find the CL 1B presets, which are
stored in a folder unique to each plug-in:
Mac OS X preset paths:
Factory presets:
<Macintosh HD>/Library/Application Support/Tube-Tech/CL 1B/Presets/
User presets:
<your user name>/Library/Application Support/Tube-Tech/CL 1B/Presets/
....continued
Tube-Tech CL 1B / 9
Windows preset paths:
Factory presets:
C:\Program Files\Tube-Tech\CL 1B\Presets\
User presets:
C:\Documents and Settings\<your user name>\My Documents\Tube-Tech\CL
1B\Presets\
•
•
To delete a preset file, simply move it to the 'Trash' or 'Recycle bin'.
To create a new sub-folder that appears in the Plug-In menu, simply create a new
folder in the Plug-In folder that resides in the PRESETS folder of the CL 1B
default preset location.
NOTE: A folder will not appear in the Preset File Menu unless it has at least one preset inside!
14 - Up/down
The UP/DOWN arrows can be used to browse through all presets.
15 - A/B
With the A/B compare function you can easily compare different parameter settings
when working with the CL 1B.
When you start working with your preset, the A/B button is grayed out. This state
indicates that the settings in both memory locations A and B are identical - so there is
actually nothing to compare.
As soon as you touch one of the parameters, the memory location "A" will be active.
All parameter changes will be applied to memory location "A". If you switch to memory
location "B", you go back to the starting point, and all further changes will now be
applied to memory location "B".
Every time you press the A/B button, you will toggle between these two memory
locations.
NOTE: The A/B memory locations are temporary settings only! Saving a preset, will
save the currently selected memory location only. The setting of the other (hidden)
memory location will not be saved!
16 - Reset
Press “Reset” to clear memories A/B and return to the originally recalled preset.
10 / Tube-Tech CL 1B
|